ГОСТ 20226-82
(СТ СЭВ 2794-80)
Группа Г16
ГОСУДАРСТВЕННЫЙ СТАНДАРТ СОЮЗА ССР
ПОДШИПНИКИ КАЧЕНИЯ. ЗАПЛЕЧИКИ ДЛЯ УСТАНОВКИ ПОДШИПНИКОВ КАЧЕНИЯ
Размеры
Rolling bearings. Shoulders for bearings mounting. Dimensions
ОКП 64 0000
Дата введения 1983-01-01
Постановлением Государственного комитета СССР по стандартам от 25 февраля 1982 г. N 831 срок введения установлен с 01.01.83
ВЗАМЕН ГОСТ 20226-74
1. Настоящий стандарт распространяется на заплечики валов и корпусов для установки подшипников качения, основные размеры которых соответствуют ГОСТ 3478-79.
Стандарт не распространяется на заплечики для установки подшипников качения по ГОСТ 9592-75 и ГОСТ 4060-78.
Стандарт полностью соответствует СТ СЭВ 2794-80.
2. Размеры заплечиков должны соответствовать указанным на черт.1-27 и в табл.1-35.
Примечание. Приведенные чертежи не определяют конструкцию подшипникового узла.
Черт.1-15. Радиальные и радиально-упорные подшипники качения
Радиальные и радиально-упорные подшипники качения
| по ГОСТ 8338-75
| по ГОСТ 7242-81
|
| по ГОСТ 10058-75*
| по ГОСТ 5720-75
|
| ________________ | |
| по ГОСТ 831-75
| по ГОСТ 832-78
|
| по ГОСТ 8882-75
| по ГОСТ 8995-75
|
| по ГОСТ 2893-82
| по ГОСТ 8328-75
|
| по ГОСТ 8328-75
| по ГОСТ 8328-75
|
| по ГОСТ 5721-75
| по ГОСТ 5377-79
|
по ГОСТ 4657-82
Черт.15
Таблица 1
Шариковые подшипники по ГОСТ 8338-75 серия ширин 1 (черт.1).
Роликовые подшипники по ГОСТ 4657-82 серия ширин 4 (черт.15)
Серия диаметров 8
мм
|
|
|
|
|
| ||
| наим. | наиб. | наиб. | наим. | |||
| 1,5 | 4 | 2,0 | - | 3,15 | - | 1,8 |
| 3,0 | 7 | 4,0 | - | 6,0 | - | |
| 4,0 | 9 | 5,0 | 5,2 | 7,8 | - | |
| 5,0 | 11 | 6,3 | 6,5 | 9,8 | 9,5 | |
| 6,0 | 13 | 7,3 | 7,5 | 11,8 | - | |
| 7,0 | 14 | 8,5 | 9,0 | 12,5 | - | |
| 8,0 | 16 | 9,8 | 10,0 | 14,0 | 13,7 | |
| 9,0 | 17 | 10,8 | 11,0 | 15,0 | - | |
| 10,0 | 19 | 12,0 | 12,5 | 17,0 | - | |
| 12,0 | 21 | 14,0 | 14,5 | 19,0 | - | 2,0 |
| 15,0 | 24 | 17,0 | 17,5 | 22,0 | - | |
| 17,0 | 26 | 19,0 | 19,5 | 24,0 | 23,8 | |
| 20,0 | 32 | 22,0 | 23,0 | 30,0 | 28,0 | |
| 25,0 | 37 | 27,0 | 27,5 | 35,0 | 34,0 | |
| 30,0 | 42 | 32,0 | 32,5 | 40,0 | 39,0 | |
| 35,0 | 47 | 37,0 | 37,5 | 45,0 | 43,5 | |
| 40,0 | 52 | 42,0 | 43,0 | 50,0 | 49,0 | |
| 45,0 | 58 | 47,0 | 48,0 | 56,0 | 54,5 | |
| 50,0 | 65 | 52,0 | 54,0 | 63,0 | 61,2 | |
| 55,0 | 72 | 57,0 | 60,0 | 70,0 | 67,0 | 3,0 |
| 60,0 | 78 | 62,0 | 64,0 | 76,0 | 74,0 | |
| 65,0 | 85 | 69,0 | 70,0 | 81,0 | 80,5 | |
| 70,0 | 90 | 74,0 | 75,0 | 86,0 | 85,5 | |
| 75,0 | 95 | 79,0 | 80,0 | 91,0 | 89,0 | |
| 80,0 | 100 | 84,0 | 85,0 | 96,0 | 94,5 | |
| 85,0 | 110 | 90,0 | 90,5 | 105,0 | 100,0 | |
| 90,0 | 115 | 95,0 | 96,0 | 110,0 | 109,0 | |
| 95 | 120 | 100,0 | 102,0 | 115,0 | 113,0 | |
| 100 | 125 | 105,0 | 107,0 | 120,0 | - | |
| 105 | 130 | 110,0 | 112,0 | 125,0 | 124,0 | |
| 110 | 140 | 115,0 | 118,0 | 135,0 | 133,0 | |
| 120 | 150 | 125,0 | 127,0 | 145,0 | 144,0 | |
| 130 | 165 | 135,0 | 137,0 | 159,0 | - | 4,0 |
| 140 | 175 | 145,0 | 149,0 | 169,0 | 167,0 | |
| 150 | 190 | 155,0 | 159,0 | 184,0 | 182,0 | |
| 160 | 200 | 165,0 | 170,0 | 194,0 | 191,0 | |
| 170 | 215 | 175,0 | 180,0 | 209,0 | 205,0 | |
| 180 | 225 | 185,0 | 190,0 | 219,0 | 215,0 | |
| 190 | 240 | 196,0 | 200,0 | 232,0 | 228,0 | |
| 200 | 250 | 206,0 | 210,0 | 242,0 | 238,0 | |
| 220 | 270 | 226,0 | 230,0 | 262,0 | 258,0 | |
| 240 | 300 | 248,0 | 250,0 | 291,0 | 285,0 | |
| 260 | 320 | 268,0 | 270,0 | 311,0 | 305,0 | |
| 280 | 350 | 288,0 | 290,0 | 341,0 | 335,0 | 5,0 |
| 300 | 380 | 310,0 | 315,0 | 370,0 | - | |
| 320 | 400 | 330,0 | 335,0 | 390,0 | 385,0 | |
| 340 | 420 | 350,0 | 355,0 | 410,0 | 405,0 | |
| 360 | 440 | 370,0 | 375,0 | 430,0 | - | |
, наим.
Таблица 2
Шариковые подшипники по ГОСТ 8338-75, ГОСТ 7242-81, ГОСТ 831-75,
ГОСТ 10058-75 серия ширин 1 (черт.1, 2, 3, 5).
Роликовые подшипники по ГОСТ 8328-75 серия ширин 1 (черт.12),
по ГОСТ 4657-82 серия ширин 4 (черт.15)
Серия диаметров 9
мм
|
|
|
|
|
|
| |
| наим. | наиб. | |||||
| 1,0 | 4 | 1,8 | - | 3,2 | 3,0 | 1,8 |
| 1,5 | 5 | 2,4 | - | 4,2 | - | |
| 2,0 | 6 | 3,2 | - | 4,8 | - | |
| 2,5 | 7 | 3,7 | - | 5,8 | - | |
| 3,0 | 8 | 4,2 | - | 7,0 | - | |
| 4,0 | 11 | 5,2 | - | 9,8 | - | |
| 5,0 | 13 | 6,6 | - | 11,5 | 11,0 | |
| 6,0 | 15 | 7,8 | 8,2 | 13,0 | - | |
| 7,0 | 17 | 9,0 | 9,5 | 15,0 | - | |
| 8,0 | 19 | 9,8 | - | 17,0 | - | |
| 9,0 | 20 | 11,0 | - | 18,0 | - | |
| 10,0 | 22 | 12,0 | 13,0 | 20,0 | - | |
| 12,0 | 24 | 14,0 | 15,0 | 22,0 | - | 2,0 |
| 15,0 | 28 | 17,0 | 18,0 | 26,0 | 25,0 | |
| 17,0 | 30 | 19,0 | 21,0 | 28,0 | 27,0 | |
| 20,0 | 37 | 22,0 | 23,0 | 35,0 | 33,5 | |
| 22,0 | 39 | 24,0 | 26,0 | 37,0 | - | |
| 25,0 | 42 | 27,0 | 28,5 | 40,0 | 38,5 | |
| 28,0 | 45 | 30,0 | 31,5 | 43,0 | - | |
| 30,0 | 47 | 32,0 | 33,5 | 45,0 | 43,5 | |
| 32,0 | 52 | 36,0 | 38,5 | 48,0 | - | |
| 35,0 | 55 | 39,0 | 40,5 | 51,0 | 50,0 | |
| 40,0 | 62 | 44,0 | 46,5 | 58,0 | 56,5 | |
| 45,0 | 68 | 49,0 | 50,5 | 64,0 | 63,2 | |
| 50,0 | 72 | 54,0 | 56,5 | 68,0 | 67,0 | |
| 55,0 | 80 | 60,0 | 61,0 | 75,0 | 74,0 | 3,0 |
| 60,0 | 85 | 65,0 | 66,0 | 80,0 | 79,0 | |
| 65,0 | 90 | 70,0 | 70,0 | 85,0 | 84,0 | |
| 70,0 | 100 | 75,0 | 78,0 | 95,0 | 94,0 | |
| 75,0 | 105 | 80,0 | 83,0 | 100,0 | 98,0 | |
| 80,0 | 110 | 85,0 | 88,0 | 103,0 | 103,0 | |
| 85,0 | 120 | 91,0 | 98,0 | 114,0 | 111,5 | |
| 90,0 | 125 | 96,0 | 99,0 | 119,0 | 116,5 | |
| 95,0 | 130 | 101,0 | 110,0 | 124,0 | 122,0 | |
| 100,0 | 140 | 106,0 | 113,0 | 134,0 | 131,5 | |
| 105,0 | 145 | 111,0 | 114,0 | 139,0 | 136,5 | |
| 110,0 | 150 | 116,0 | 123,0 | 144,0 | 141,0 | |
| 120,0 | 165 | 127,0 | 133,0 | 159,0 | 155,0 | |
| 130,0 | 180 | 137,0 | 148,0 | 172,0 | 169,0 | 4,0 |
| 140,0 | 190 | 147,0 | 158,0 | 182,0 | 179,0 | |
| 150,0 | 210 | 158,0 | 172,0 | 201,0 | 198,0 | |
| 160,0 | 220 | 168,0 | 173,0 | 211,0 | 207,0 | |
| 170,0 | 230 | 178,0 | 183,0 | 221,0 | 217,0 | |
| 180,0 | 250 | 188,0 | 193,0 | 241,0 | 237,0 | |
, наиб.